Hot Melt Applicator
| Price : | ＄4500.00 |
| Quantity : | 20 (set) |
| Minimum Order : | 1 |
| Product Status : | New |
| Sample Available : | yes |
| Shipment Terms : | fob,cfr,cif,Negotiable |
| Payment Mode : |
T/T |
| Categories : | Machinery, Machinery for Glass & Ceramics |
| Posted By : | Saint Best Group |
Description
HOT MELT MACHINE, Hot Melt Dispenser, Hot Melt Applicator,
Item specifics
Certification: CEBrand Name: SAINT BESTMachine Type: Glass Coating MachinePlace of Origin: China (Mainland), ShandongModel Number: SBT-HMDB
Specifications
Machine Name
HMD-B HOT MELT MACHINE
General Description
HMD-B HOT MELT MACHINE is designed for the hot melt of insulating glass with aluminum spacer. It is of the second generation of equipment with the same model. It is small and light, easy to operate and repair and has stable control over temperature. Operation can be carried out after preheating of half an hour.
Technical Index
Power Supply: Frequency: 50Hz
Voltage: three-phase five-wire system 380V
Total power: 5.5KW
Extruding Speed: above 1000g/min
Dimension (length × width × height): 550×500×920 (mm)
Total Weight: 100kg
Installation and Trial Run
a) No special conditions are required except that the operation site is kept clean.
b) Make sure the power be connected correctly in accordance with the requirements.
c) Put the designated rubber block in the rubber box, set the temperature (reference degree being 150°C-170°C) and preheat it for about 30 minutes.
d) When the set temperatures of the rubber and rubber pipe have been satisfied, triggering the rubber gun can extrude the hot melt.
Special Explanations
a) The extruding speed could be regulated, which is advised not to be too fast in the beginning. In view of different temperatures of different points in the hot melt when it is first extruded, a small amount of extrusion is recommended before formal extrusion is carried out.
b) The operation should not be conducted unless the rubber pump reaches its set temperature. (Inside the machine, protective setting is designed, so the motor will not work if set temperature is not satisfied.)
c) The fluid rubber level should be kept above the heater by adding the rubber blocks timely according to its consumption.
d) The inclusion of foreign matter is strictly prohibited to protect the machine.
e) After operation, leave enough rubber in the rubber box for next heating and then turn off the power.
f) Hang the rubber gun on the slinger when it is not used.
Note: Do not touch the gun mouth and the cover of the rubber box to avoid injury.
HOT MELT MACHINE, Hot Melt Dispenser, Hot Melt Applicator, Hot Melt Extruder, Hot Melt Extruder Machine, Hot Melt Sealant, Hot Melt Adhesive Dispenser, Glass Coating Machine
Item specifics
Certification: CEBrand Name: SAINT BESTMachine Type: Glass Coating MachinePlace of Origin: China (Mainland), ShandongModel Number: SBT-HMDB
Specifications
Machine Name
HMD-B HOT MELT MACHINE
General Description
HMD-B HOT MELT MACHINE is designed for the hot melt of insulating glass with aluminum spacer. It is of the second generation of equipment with the same model. It is small and light, easy to operate and repair and has stable control over temperature. Operation can be carried out after preheating of half an hour.
Technical Index
Power Supply: Frequency: 50Hz
Voltage: three-phase five-wire system 380V
Total power: 5.5KW
Extruding Speed: above 1000g/min
Dimension (length × width × height): 550×500×920 (mm)
Total Weight: 100kg
Installation and Trial Run
a) No special conditions are required except that the operation site is kept clean.
b) Make sure the power be connected correctly in accordance with the requirements.
c) Put the designated rubber block in the rubber box, set the temperature (reference degree being 150°C-170°C) and preheat it for about 30 minutes.
d) When the set temperatures of the rubber and rubber pipe have been satisfied, triggering the rubber gun can extrude the hot melt.
Special Explanations
a) The extruding speed could be regulated, which is advised not to be too fast in the beginning. In view of different temperatures of different points in the hot melt when it is first extruded, a small amount of extrusion is recommended before formal extrusion is carried out.
b) The operation should not be conducted unless the rubber pump reaches its set temperature. (Inside the machine, protective setting is designed, so the motor will not work if set temperature is not satisfied.)
c) The fluid rubber level should be kept above the heater by adding the rubber blocks timely according to its consumption.
d) The inclusion of foreign matter is strictly prohibited to protect the machine.
e) After operation, leave enough rubber in the rubber box for next heating and then turn off the power.
f) Hang the rubber gun on the slinger when it is not used.
Note: Do not touch the gun mouth and the cover of the rubber box to avoid injury.
HOT MELT MACHINE, Hot Melt Dispenser, Hot Melt Applicator, Hot Melt Extruder, Hot Melt Extruder Machine, Hot Melt Sealant, Hot Melt Adhesive Dispenser, Glass Coating Machine
 |
|
